Nemco-food-equipment Food Waste Disposers - Busboy Operations Manual Bedienungsanleitung PDF herunterladen

OPERATING AND INSTALLATION INSTRUCTIONS

Models: B250, B300, B750, B1000, B1500, B2000, B3000, B4000

SAFETY INSTRUCTIONS

1. WARNING – To avoid risk of injury, do not operate the unit unless properly installed to the busboy cone or mounting flange

specified in the instructions.

2. Installation of disposers must be performed by qualified personnel.

3. Please read instructions before installing and using this appliance.

4. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and

injury.

INSTALLATION – B250 DISPOSER

1. The sink mount comes already assembled in the proper order. To install to the sink, the sink flange must be removed.

2. Remove the three nuts to separate the sink mount from the disposer.

3. Loosen the three adjusting screws until the snap ring becomes exposed and remove it from the sink flange.

4. Remove the sink flange and drop it down through the sink opening making sure to seal it properly with appropriate sealant.

5. Assemble the sink flange to the sink mount and back to the disposer in the reverse order.

6. Check for leaks.

7. Wire the unit following the appropriate schematic on the following pages. Use wire suitable for 90°C minimum.

INSTALLATION – ALL OTHER DISPOSERS

1. If installing to an existing cone, an adapter kit may be needed. Call customer service for proper sizing. Installation instructions

will be provided with the adapter kit.

2. If new installation, a cone or sink flange will need to be welded into the sink for mounting. Consult parts list for available

flanges.

3. Once a flange has been welded into the sink, the disposer is mounted to the bottom of it.

4. Place the slotted gasket over the top of the disposer hopper so that the holes line up. Raise it up to the sink flange.

5. If the disposer is provided with the three support posts, loosen the set screw and drop the legs to the floor to support the

disposer and then tighten the set screws back again.

6. Place the (3) adapter segments over the sink flange so that the holes line up with the holes in the hopper.

7. Place the (6) screws down through the segments and into the hopper. Tighten the screws and check for leaks.

8. A water line must be plumbed to the disposer’s hopper making sure the minimum water requirements are met as listed below.

½ HP require 2 gpm / 1 HP require 3 gpm / 1½ - 3 HP require 5 gpm / 4 HP and up require 8 gpm

9. Wire the unit following the appropriate schematic on the following pages. Use wire suitable for 90°C minimum.

OPERATION

1. This disposer is designed to accommodate food waste only, do not place any trash in the disposer. Do not place any foam,

wood, foil, rubber, glass, or clothes in the disposer as these will jam the machine.

2. Greases, oils, and drain cleaners will damage the gaskets and should also be avoided.

3. Some foods wastes can damage the disposer and should not be ran through it. These are large whole bones, clam or oyster

shells, and whole corn husks.

4. Turn on the disposer and make sure water is running into the hopper before feeding any food into the drain. Feeding food into

the disposer before turning it on may cause the unit to jam.

5. Be sure all food waste has been disposed before turning the disposer off.

6. If a time delay relay is being used, it must be set for a cycle of not less than two minutes. This makes sure all food has been

flushed through the drain and minimizes the risk of a stoppage.

MAINTENANCE

1. Wipe the disposer down with a damp cloth daily, do not spray the unit down with water as this will damage the motor.

2. Check the cutting table wear once a month. As the cutting table wears, the disposer will allow larger food to pass through the

drain. If the wear becomes excessive, a stoppage may occur.

3. If the cutting table has a visible gap between it and the cutting sleeve, then it is time to rebuild the disposer.

TROUBLESHOOTING

Motor Not Turnin

urn power off. Check to make sure motor is not jammed. With

the power off, motor should turn freely

urn the Power off. Check for a faulty switch, reversing switch,

solenoid valve, or contactor. (This should be done by qualified

personnel or service technicians only)

Press the reset button located on the junction box on the motor

Check the circuit breaker to make sure it is operational

Motor Does Not Stop Turnin

In a situation that

the motor does not stop turning,

disconnect

power from the motor to prevent damage to the motor. This may

require turning the circuit breaker off. Have a service agent or

qualified personnel check for a faulty switch, reversing switch,

solenoid valve, or contactor.

1 2 3

Inhaltsverzeichnis

Seite 1

OPERATING AND INSTALLATION INSTRUCTIONS Models: B250, B300, B750, B1000, B1500, B2000, B3000, B4000 SAFETY INSTRUCTIONS 1. WARNING – To avoi

Seite 2

WIRING SCHEMATICS

Seite 3 - 419-542-6690 Fax 47997

301 Meuse Argonne Hicksville, OH 43526 1-800-782-6761 Toll Free 419-5

Kommentare zu diesen Handbüchern

Keine Kommentare

Nemco-food-equipment Food Waste Disposers - Busboy Operations Manual Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Küche Nemco-food-equipment Food Waste Disposers - Busboy Operations Manual herunter. Nemco Food Equipment Food Waste Disposers - Busboy Operations Manual User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küche Nemco-food-equipment Food Waste Disposers - Busboy Operations Manual